深圳酒店不銹鋼制作時的涂好感光油墨烘干的作用！

    在企業制作標識牌不鋼剛時，有時會需要絲印一些圖案，作為標識牌制作公司，把涂好感光油墨的不銹鋼板放在烘箱里，溫度設置在88度，烘的時間為15到20分鐘。這個時間需要把握好時間度，時間的控制和溫度的控制，是整個過程的最關健點，在標識牌烘干后，把吹風機調到冷風檔，給不銹鋼板降溫，也可以讓它自然降溫。自然體現企業品牌的形象設計。

    酒店標識牌制作時的印刷曝光來制作一些圖案紋理。
    我們在標識牌時，企業的標識牌設計創意就是如下開始的，下面到kR-B1型單面真空曝光機上進行曝光。這是需要一些設備來處理這些問題的。在先接通電源，控制面板上的電流表顯示為8安-10安，將機器預熱3分鐘左右，即可正常工作。將菲林片與不銹鋼板對齊并使兩者充分接觸，然后讓不銹鋼板在上面，菲林片在下面，平穩地放在單面真空曝光機工作臺面上。一定要注意這些表面的干凈一些，否則就會一一些印子在上面，這樣做的標識牌就沒那么好看了。

    企業品牌創意設計，就用這些品牌來設計過的，我們在制作時取出不銹鋼板和菲林。這就是曝光后的不銹鋼板，用肉眼看上去，沒有任何變化。再曝光工作完成后，一定要過5分鐘，讓曝光機內的燈管冷卻后，再關閉總電源。這樣就把這些酒店的不銹鋼標牌制作完成的了。

Coated stainless steel business is good when the role of light-sensitive ink drying!

     Signage in the corporate production of stainless steel just, sometimes need to screen some of the design, production companies as signage, good light-sensitive ink to coated stainless steel plate on the oven, the temperature set at 88 degrees, bake time is 15 to 20 minutes. This time need a good grasp of time, time control and temperature control, the whole process is the most Key points in the identification card, after drying, the hair dryer transferred to the cold file, to the stainless steel plate cooling, you can let it cool down . Naturally reflect the corporate brand image design.

     Identification card when making the printing exposure to make some of the texture pattern.
     We signage, corporate logo design creative brand is as the beginning of the following to the kR-B1-type vacuum exposure machine on single exposure. This is some of the equipment needed to deal with these issues. Earlier power, current meter on the control panel display is 8 -10 An An, preheat the machine about 3 minutes, you can work. Films will be aligned with the stainless steel plate and make full contact between the two, and then let the stainless steel plate on the top film sheet below, smooth on one side vacuum exposure machine work surface. Must pay attention to some of these surfaces clean, otherwise it will mark a number on it, so do not be so good-looking signage.

     Brand creative design, we use these brands to design before, when we made ​​out of stainless steel plates and film. This is the exposure of the stainless steel plate, with the naked eye, without any change. Re-exposure is completed, must be over 5 minutes to allow the lamp cooling exposure machine, then turn off the power. This put them in the hotel finished a stainless steel plate.